Sixth Army Group

Sixth Army Group (http://www.sixtharmygroup.com/forums/index.php)
-   Training Center (http://www.sixtharmygroup.com/forums/forumdisplay.php?f=28)
-   -   Making the M-1 Garand Web Sling: A Tutorial (http://www.sixtharmygroup.com/forums/showthread.php?t=23408)

Panzercommander HOH 02-18-2020 11:51 PM

Making the M-1 Garand Web Sling: A Tutorial
 
Making The M-1 Garand Web Sling: A Tutorial



https://live.staticflickr.com/65535/...21524c65_c.jpg



A brief history on the real thing:

Approved by the Quartermaster in late 1942, the web sling for the M-1 Garand was designed as a cheaper and easier to use replacement for the M-1907 leather sling. The web sling first saw combat in 1943, and was rather widespread by 1944 and certainly more so by 1945. Though it never fully replaced the M-1907 leather sling; it more than did its part helping troops keep their rifles slung during the war.


When I began to work on late war US subjects, I picked up one of Battlegear Toys' M-1923 web slings to add some variety in the ranks. I did not know that it was the M-1923 web sling at the time I bought it though. When I finally got around to fitting it to a rifle, I found I had no idea how to do so. The Battlegear Toys website merely shows the following:

https://live.staticflickr.com/65535/...bbece4a6_c.jpg

Pictured Above: The BGT M-1923 web sling attached to a M-1 Garand


The M-1923 web sling was developed during the inner-war years as a less expensive cloth replacement for the M-1907 leather sling while retaining its adjustability for marksmanship. However, it is not very common. Large existing stocks of the M-1907 sling produced during WWI lasted the military until the beginning of WWII and the M-1923 web sling is apparently ridiculously complicated to attach to a rifle.


Though I didn't know it yet, I did not know which web sling I purchased from BGT. I fumbled around the internet for information on the sling and all I found was information on the M-1 web sling. I thought BGT got it wrong (they did not). I was looking at two different types of US web sling.



So, if you buy the BGT M-1923 sling you may leave it as is and it is perfectly fine.

However, if you're interested in modifying it into the more widely used M-1 web sling like I did, continue reading below.



What you'll need:

https://live.staticflickr.com/65535/...dc77bc67_c.jpg

1. A M-1 Garand (I'm using my favorite version, the DML RTV first pattern M-1 Garand (non-breakable-downable)

2. A DiD Buck Jones Springfield/trench shotgun web sling keeper buckle

3. A small friction buckle (5 mm - measured outside to outside)

4. A DiD Buck Jones Springfield/trench shotgun web sling metal end tab

5. A BGT M-1923 web sling


https://live.staticflickr.com/65535/...a9f0b229_c.jpg

Hardware Close-Up:

1. A DiD Buck Jones Springfield/trench shotgun web sling keeper buckle

2. A 5 mm (measuring outside to outside) friction buckle

3. A DiD Buck Jones Springfield/trench shotgun web sling metal end tab


The DiD Buck Jones Springfield/trench shotgun web sling keeper buckle and the metal end tab can be seen on both weapons here:

https://live.staticflickr.com/65535/...2bfd8c73_c.jpg


You can find the 5 mm friction buckle on some of the following German items:

https://live.staticflickr.com/65535/...be0f843e_c.jpg

1. The straps to the Soldier Story German Feldgendarme's gas cape pouch

2. DML German binocular straps


You will also need some metal to make the J-hook to clip on the sling swivel on the stock of the rifle. I used a pop can:

https://live.staticflickr.com/65535/...22e37165_c.jpg


Tools Needed:


https://live.staticflickr.com/65535/...b4db8080_c.jpg

1. Ruler

2. Toothpick

3. Small Needle Nose Pliers

3. Scissors

4. Cutters

5. Flat Black Paint

6. Paint Brush

7. Tweezers

8. Fabri-Tac



The BGT M-1923 web sling looks like this straight out of the package:


https://live.staticflickr.com/65535/...40375f38_c.jpg


You'll want to take it apart using the tweezers so it looks like this:


https://live.staticflickr.com/65535/...12fdd0f1_c.jpg


Save the D ring as you will need it to make the sling. Save everything else as it can be used for another project (more on that later).



Take the longest of the two portions of the BGT M-1923 web sling and run the unpainted end of it through the 5 mm friction buckle. Fabri-Tac the end back to itself just after the friction buckle like this:


https://live.staticflickr.com/65535/...5b423726_c.jpg



Slide the D ring on the web sling with the D curvature facing out. The small end of the web sling that you Fabri-Tac'ed down after the 5 mm friction buckle should face down (opposite side of the D curvature of the D ring):


https://live.staticflickr.com/65535/...58446489_c.jpg


Set that aside for a moment.



Making the J-hook:

This part requires a bit of blacksmithing, but it isn't insurmountable by any means.

Cut out a chunk of the pop can (these are remarkably thin these days...). Being that it is so thin, fold it over on itself and form a straight edge.

Cut it down to a manageable size.

Take your ruler and measure out and mark 15 mm on the aluminum:


https://live.staticflickr.com/65535/...af4e9b7f_c.jpg


Then measure a 5 mm width on the aluminum:


https://live.staticflickr.com/65535/...c71c302f_c.jpg



Once you've fashioned the 5 mm wide by 15 mm long rectangular piece, you're going to bend it into an "S" shape:


https://live.staticflickr.com/65535/...63bca5f3_c.jpg


Like this:


https://live.staticflickr.com/65535/...4091376c_c.jpg


Now take the cutters and round each end of the "S" shape:


https://live.staticflickr.com/65535/...85b7b707_c.jpg


Once you've rounded the ends, paint it flat black:


https://live.staticflickr.com/65535/...fdb2371d_c.jpg


Et voilą ! This is your J-hook.


Now set the J-hook aside for a moment.


Get your M-1 Garand, the web sling you've already started, and the DiD Buck Jones keeper buckle back out.


https://live.staticflickr.com/65535/...5bed48a4_c.jpg


Making sure you do not twist the sling, run the black painted end of the web sling through the 5 mm friction buckle. It is a tight fit, you may need to trim the black painted web sling end down to a point to get it through the 5 mm friction buckle. It also might fray when you are running it through the friction buckle.


Now, open up the keeper on the DiD Buck Jones keeper buckle and run it through the black painted end of the web sling, hinge side first:


https://live.staticflickr.com/65535/...a2bdd4b3_c.jpg


Making sure you do not twist the sling, take the black painted web sling end loop it through the middle sling swivel (the second one from either end of the gun) and then run it back through the DiD Buck Jones keeper buckle (on top of itself). Clamp the keeper shut. Trim any fraying ends from the painted end of the web sling. Glue the DiD Buck Jones webbing end tab on the end of the freshly trimmed web sling end.


https://live.staticflickr.com/65535/...7b3a9165_c.jpg


Grab the "S" shaped J-hook that you made. run one of the clipped ends through the sling swivel on the butt of the rifle so the clipped end points towards the rest of the rifle:


https://live.staticflickr.com/65535/...bf2f5549_c.jpg



Run the other clipped end of the J-hook through the D ring on the web sling. That clipped end will point back at the end of the stock. Using the needle nose pliers, clamp the clipped ends of the J-hook down on itself, locking the J-hook around the swivel sling on the stock and around the D ring on the web sling:


https://live.staticflickr.com/65535/...9d9620c3_c.jpg



And there you have it! You've made a much more accurate version of the M-1 Garand web sling!


Finished Product:


https://live.staticflickr.com/65535/...21524c65_c.jpg


I've made eight:


https://live.staticflickr.com/65535/...1d4d9d85_c.jpg



You can take the short end of the remaining BGT sling and one of the BGT friction buckles to make leg ties for your paratroopers:


https://live.staticflickr.com/65535/...7a0fdc06_c.jpg


(These leg ties are nearly identical to the ones sold on the BGT website...)



Finally, the sling in action:


https://live.staticflickr.com/65535/...bfb7a518_c.jpg

https://live.staticflickr.com/65535/...02544a26_c.jpg

https://live.staticflickr.com/65535/...7673eeca_c.jpg

https://live.staticflickr.com/65535/...f1e8b2a5_c.jpg



Links / References:


The BGT M-1923 Web Sling:

https://battlegeartoys.com/collectio...-s-rifle-sings


Installing a 1:1 M-1 Garand Web Sling:

https://www.youtube.com/watch?v=jsyno5o1rY8


At The Front: Garand Sling, Web, OD No. 3:

https://www.atthefront.com/M1-Garand...-p/uswm1gw.htm



Questions? Just ask! I'd be happy to help!

Pangaea95 02-19-2020 12:17 AM

Re: Making the M-1 Garand Web Sling: A Tutorial
 
Great tutorial, gonna have to give this a try!!!

Panzercommander HOH 02-19-2020 07:21 PM

Re: Making the M-1 Garand Web Sling: A Tutorial
 
Erratum: (et al.)


I misidentified the BGT sling; it is indeed a M-1923 web sling, and is not wrong. I have corrected the text of my tutorial to reflect this.


Also, for those of you who own the BBi M9A1 Bazooka from Lefty McGill, you already own a mass produced version of this sling, complete with "S" hook:


The BBi M9A1 Bazooka:

https://live.staticflickr.com/65535/...ea89fa28_c.jpg


Close Ups of the sling:

https://live.staticflickr.com/65535/...e15287a4_c.jpg

https://live.staticflickr.com/65535/...6c16bc12_c.jpg

https://live.staticflickr.com/65535/...41678cb7_c.jpg


Thank you to Santos Airlann Balaton for brining both of these facts to my attention on Facebook.

Panzercommander HOH 02-19-2020 07:23 PM

Re: Making the M-1 Garand Web Sling: A Tutorial
 
Quote:

Originally Posted by Pangaea95 (Post 204370)
Great tutorial, gonna have to give this a try!!!


You're welcome, Randy!

Best of luck!

Hope they turn out well for you!

- Fred

Hammer's Africaners 02-22-2020 10:20 PM

Re: Making the M-1 Garand Web Sling: A Tutorial
 
Great tutorial

Panzercommander HOH 02-23-2020 01:43 AM

Re: Making the M-1 Garand Web Sling: A Tutorial
 
Thanks, Peter!

- Fred


All times are GMT. The time now is 10:03 PM.

vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
©2005 - 2015 www.sixtharmygroup.com